Uzyskaj wycenę
Konto
Wyloguj się
Uzyskaj wycenę
24V Truck Parking A/C Battery Runtime: How to Size a 25.6V 300Ah Pack
Poradniki OEM/ODM i produkcji

24V Truck Parking A/C Battery Runtime: How to Size a 25.6V 300Ah Pack

A 24V truck parking air conditioner battery should be sized from the energy the cab actually uses during a rest period. An amp-hour label alone cannot tell a fleet buyer how many hours of cooling to expect. This guide is for distributors, vehicle integrators and fleet procurement teams comparing a 25.6V LiFePO4 auxiliary battery for a compatible 24V parking A/C system.

Is a 25.6V LiFePO4 battery suitable for a 24V truck parking A/C?

25.6V is a nominal LiFePO4 battery voltage used in the 24V system class. Compatibility still depends on the actual charging voltage, the A/C input range, low-voltage cut-off settings and vehicle architecture. A 24V-class label does not mean that every component operates at exactly 24.0V.

First identify the parking cooler's exact model and supply voltage. Dometic's RTX1000/RTX2000 operating manual, technical-data section lists separate 12V and 24V versions. This is a useful reminder to check the specific unit rather than infer voltage from the truck's size or country of use. A 25.6V pack must not be connected directly to a 12V-only cooler.

Compare batteries in watt-hours as well as amp-hours. For an illustrative 25.6V, 300Ah configuration, the calculation is 25.6V × 300Ah = 7,680Wh = 7.68kWh nominal. These inputs are a worked sizing example, not verified ratings for the LFP25.6-300 reference code. Actual nominal and usable energy must be confirmed in the technical sheet for the supplied battery.

How to calculate 24V truck parking air conditioner battery runtime

Use average electrical demand over the intended rest period, including the other equipment drawing from the same battery. Cooling capacity is a different measurement: a cooler advertised with 2,000W of cooling output does not automatically draw 2,000W of electrical input. Dometic's RTX2000 24V product specification separates cooling capacity from input voltage and current consumption.

Estimated runtime (hours) = nominal battery energy (kWh) × usable energy fraction ÷ average total battery-side draw (kW).

For the table, assume a new battery at suitable temperature, starting at 95% state of charge (SOC) and stopping at a 15% reserve. That gives an illustrative 80% energy window: 7.68 × 0.80 = 6.144kWh. This window is a calculation assumption, not a specified operating recommendation or warranty condition.

Calculated examples for a 25.6V 300Ah battery with a 6.144kWh planning budget
Assumed average total battery-side drawCalculationEstimated runtime
300W (0.30kW)6.144 ÷ 0.3020.5 hours
500W (0.50kW)6.144 ÷ 0.5012.3 hours
700W (0.70kW)6.144 ÷ 0.708.8 hours
1,000W (1.00kW)6.144 ÷ 1.006.1 hours

These loads are hypothetical scenarios, not measurements of a particular cooler or a Zhuosheng field test. Battery-side draw includes power taken by the A/C, any conversion losses and other connected loads. Do not deduct an additional inverter-efficiency factor if those losses are already included in the measurement. If you only have appliance-side figures, account for conversion losses and auxiliaries before using the formula.

For an eight-hour target at an assumed 500W total average draw, the energy requirement is 0.50 × 8 = 4.0kWh. Dividing by the illustrative 0.80 usable fraction gives 5.0kWh nominal before adding a project-specific allowance for uncertainty, temperature and capacity loss with age. At 1,000W, the same eight hours would require 8.0kWh of usable energy, exceeding this example's 6.144kWh budget.

Measure the sleeper-cab load before promising an overnight runtime

A cooler can draw heavily while cooling a hot cab and then cycle or reduce output once the set temperature is reached. Outdoor temperature, direct sun, insulation, window covers, air leakage and the selected temperature all change the load. A short reading taken after sunset may not represent a hot afternoon rest period.

Sleeper bunk, fabric seat and curtains inside a parked long-haul truck cab
Cab temperature, insulation and other overnight electrical loads belong in the same battery energy budget.
  1. Define the rest period. Record the hours, expected outdoor temperature, parking conditions and target cabin temperature.
  2. Log energy at the battery. Have the integrator use a suitable DC energy meter or correctly installed battery monitor over a representative cycle. Record watt-hours, average power and peak current.
  3. Include the other loads. Add the refrigerator, lighting, electronics, controls and any battery heater supplied from the same pack. Check that the meter captures all discharge paths.
  4. Check a harder operating case. Repeat under the conditions the buyer actually needs, while staying within the equipment limits, and retain the required reserve.

Energy measurement and SOC monitoring are related but different tasks. Victron Energy's Lithium Smart Battery manual, battery-monitoring section explains the need for suitable monitoring hardware in its own systems. For another brand's installation, confirm what its supplied monitor measures and how SOC is calibrated.

Check power delivery and charging as carefully as battery capacity

Energy capacity determines the possible duration; current limits determine whether the pack can support the equipment at all. A BMS current rating alone does not establish compatibility with a particular cooler or engine starter. Check continuous demand, startup transients, protection settings and temperature-related derating against the technical documents for the exact supplied configuration.

  • Voltage: confirm the cooler's permitted input range against the complete battery operating and charging range.
  • Starter isolation: identify whether the parking loads use a separate auxiliary bank. Preserve the vehicle's required starting reserve and approved isolation arrangement.
  • Charging: verify the lithium charging profile, current limit and available charging time for the exact battery and vehicle.
  • Protection and mounting: have the responsible installer confirm cable sizing, fusing, secure mounting, vibration suitability and environmental protection.
  • Cold conditions: verify charging and discharging limits separately, plus any heater's activation logic and energy use.

Direct alternator charging needs particular attention. Victron Energy's system-design manual, section 3.4 on alternator charging discusses the high charge acceptance of lithium batteries and current-limiting approaches. The appropriate charger, regulator and settings for a Zhuosheng installation must be confirmed for the actual vehicle; Victron-specific battery settings should not be copied across automatically.

For a retrofit, use the checks in our lead-acid to LiFePO4 replacement guide. For winter projects, our LiFePO4 cold-weather charging checklist explains why heating support does not remove the need to verify temperature limits.

A truck parking battery configuration enquiry for B2B buyers

Use the Zhuosheng truck parking A/C battery configuration enquiry to discuss a compatible auxiliary-power project. Product-specific ratings for the LFP25.6-300 reference code have not been verified. This guide's 25.6V, 300Ah and 7.68kWh figures are illustrative calculation inputs, not a specification or measured result for a supplied product.

Worked sizing reference — not a confirmed product specification
Illustrative voltage / capacity inputs25.6V / 300Ah (worked example only)
Calculated nominal energy of the example7.68kWh (not a verified product rating)
Application to discussCompatible truck parking A/C and auxiliary vehicle power
Project approval requiresThe current technical sheet, supplied-unit label and confirmation of the complete vehicle system

Before ordering, reconcile the supplied-unit label with the current model-specific technical sheet, including rated energy, continuous and peak current, temperature limits and dimensions. These must agree for the configuration being supplied. Confirm physical fit, environmental requirements, charger compatibility and the intended auxiliary-power duty before vehicle approval.

What to include in a truck parking battery RFQ

  • Truck make, model, model year and the voltage of the relevant electrical circuit.
  • Parking A/C make, model, input range and available electrical consumption data.
  • Target rest hours, climate, measured battery-side energy and all other loads.
  • Battery space, mounting arrangement, available payload and terminal access.
  • Alternator, DC-DC or shore charger details and time available to recharge.
  • Required quantity, destination and any model-specific documentation needed for the project.

Frequently asked questions

Will a 300Ah battery run a truck air conditioner all night?

It depends on voltage, usable energy and average demand. In this guide's 25.6V example, an illustrative 80% energy window gives about 12.3 hours at 500W total battery-side draw, or 6.1 hours at 1,000W. Measure the actual rest-period load and retain the required reserve before promising overnight operation.

Is a 25.6V battery the same as a 24V battery?

A 25.6V nominal LiFePO4 pack belongs to the 24V system class, but the labels alone do not establish compatibility. Compare the battery's full operating and charging range with the cooler and charger specifications. A 12V-only appliance requires its own compatible supply and must not be connected directly to this pack.

Does a high-current BMS mean the battery can start the truck?

No. A BMS current rating is not an engine-starting specification. Starting duty involves transient current, voltage sag, protection behavior and vehicle approval requirements. Evaluate the battery for its documented application and obtain explicit confirmation for any proposed starter function rather than inferring it from a BMS label.

Can the truck alternator recharge a LiFePO4 parking battery?

A suitable charging system can use alternator energy, but direct connection should not be assumed. The vehicle integrator must confirm voltage regulation, current limiting, isolation, alternator thermal capacity and battery charging limits. The available driving time must also be enough to replace the energy consumed during the parked rest period.

Choose the battery around the rest period

The right 24V truck parking air conditioner battery matches a measured energy budget, the required reserve and an approved charging arrangement. For the 25.6V 300Ah example, 7.68kWh is the nominal starting point; realistic usable energy and total battery-side demand determine the planned runtime.

Request a truck parking battery configuration and quote

Send Shenzhen Zhuosheng New Energy Technology Co., Ltd. the RFQ details above to discuss the battery specification for your project.

Method and sources, reviewed 9 November 2026: The voltage and capacity inputs are illustrative; model-specific ratings for the linked configuration enquiry have not been verified. The runtime table is an arithmetic illustration using nominal voltage, rated capacity, a stated usable energy assumption and hypothetical average loads. Dometic documentation supports the distinction between cooler electrical input and cooling output; Victron Energy documentation supports the charging and monitoring principles cited above. Equipment-specific limits must come from the respective current manuals.

LiFePO4 Batteries in Cold Weather: Charging Limits and Checklist

Uzyskaj wycenę

Jeśli masz pytania dotyczące naszej gamy produktów lub usług, wypełnij poniższy formularz kontaktowy, a skontaktujemy się z Tobą natychmiast
produkt

Uzyskaj wycenę

Jeśli masz pytania dotyczące naszej gamy produktów lub usług, wypełnij poniższy formularz kontaktowy, a skontaktujemy się z Tobą natychmiast
produkt